List of International Organization for Standardization standards

This is a list of published [Note 1] International Organization for Standardization (ISO) standards and other deliverables. [Note 2] For a complete and up-to-date list of all the ISO standards, see the ISO catalogue. [1]

The standards are protected by copyright and most of them must be purchased. However about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 ( JTC1) have been made freely and publicly available. [2]

ISO 1 – ISO 99

  • ISO 1:2016 Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties
  • ISO 2:1973 Textiles – Designation of the direction of twist in yarns and related products
  • ISO 3:1973 Preferred numbers – Series of preferred numbers
  • ISO 4:1997 Information and documentation – Rules for the abbreviation of title words and titles of publications
  • ISO 5 Photography and graphic technology – Density measurements
  • ISO 6:1993 Photography – Black-and-white pictorial still camera negative film/process systems – Determination of ISO speed
  • ISO 7 Pipe threads where pressure-tight joints are made on the threads
  • ISO 8:1977 Documentation – Presentation of periodicals
  • ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters into Latin characters – Slavic and non-Slavic languages
  • ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins
  • ISO 12:1987 Aerospace – Pipelines – Identification
  • ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering – Dimensions, tolerances and verification
  • ISO 15:2017 Rolling bearings – Radial bearings – Boundary dimensions, general plan
  • ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch)
  • ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers
  • ISO 18:1981 Documentation – Contents list of periodicals
  • ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor chains
  • ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys – Dimensions and tolerances
  • ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—Specifications
  • ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—Specifications
  • ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for direct front projection—Specifications
  • ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture film—Specifications
  • ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-picture film for direct front projection—Specifications [Withdrawn without replacement]
  • ISO 31 Quantities and units [withdrawn: replaced with ISO/IEC 80000]
  • ISO 32:1977 Gas cylinders for medical use—Marking for identification of content
  • ISO 34 Rubber, vulcanized or thermoplastic—Determination of tear strength
    • ISO 34-1:2015 Part 1: Trouser, angle and crescent test pieces
    • ISO 34-2:2015 Part 2: Small (Delft) test pieces
  • ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability
  • ISO 36:2017 Rubber, vulcanized or thermoplastic—Determination of adhesion to textile fabrics
  • ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
  • ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps [withdrawn without replacement]
  • ISO 43:2016 Aircraft—Jacking pads
  • ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—Directions of operation
  • ISO 45:1990 Aircraft—Pressure refuelling connections
  • ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets
  • ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100 IRHD)
  • ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1
  • ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 [Withdrawn without replacement]
  • ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile
  • ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—Modules
  • ISO 55:1977 Seedlac—Specification [Withdrawn without replacement]
  • ISO 57:1975 Bleached lac—Specification [Withdrawn without replacement]
  • ISO 60:1977 Plastics—Determination of apparent density of material that can be poured from a specified funnel
  • ISO 61:1976 Plastics—Determination of apparent density of moulding material that cannot be poured from a specified funnel
  • ISO 62:2008 Plastics—Determination of water absorption
  • ISO 63:1975 Flat transmission belts—Lengths [Withdrawn: Replaced with ISO 22]
  • ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
  • ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size [Withdrawn without replacement]
  • ISO 68 ISO general-purpose screw threads – Basic profile
    • ISO 68-1:1998 Part 1: Metric screw threads
    • ISO 68-2:1998 Part 2: Inch screw threads
  • ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting and perforating dimensions
  • ISO 70:1981 Cinematography—35 mm negative photographic sound record on 35 mm motion-picture film—Position and maximum width dimensions
  • ISO 71:2014 Cinematography—16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions
  • ISO 74:1976 Cinematography—Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film—Positions and dimensions
  • ISO 75 Plastics—Determination of temperature of deflection under load
    • ISO 75-1:2013 Part 1: General test method
    • ISO 75-2:2013 Part 2: Plastics and ebonite
    • ISO 75-3:2004 Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
  • ISO 76:2006 Rolling bearings—Static load ratings
  • ISO 78 Chemistry — Layouts for standards [Note 3]
    • ISO 78-2:1999 Part 2: Methods of chemical analysis
    • ISO 78-3:1983 Part 3: Standard for molecular absorption spectrometry [Withdrawn without replacement]
    • ISO 78-4:1983 Part 4: Standard for atomic absorption spectrometric analysis [Withdrawn without replacement]
  • ISO/TR 79:2015 Reference materials - Examples of reference materials for qualitative properties
  • ISO 82:1974 Steel—Tensile testing [Withdrawn: replaced with ISO 6892-1]
  • ISO 83:1976 Steel—Charpy impact test (U-notch) [Withdrawn: replaced with ISO 148-1]
  • ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than 0,5 mm thick [Withdrawn: replaced with ISO 6892-1]
  • ISO 89:1974 Steel—Tensile testing of wire [Withdrawn: replaced with ISO 6892-1]
  • ISO 90 Light gauge metal containers—Definitions and determination of dimensions and capacities
    • ISO 90-1:1997 Part 1: Open-top cans
    • ISO 90-2:1997 Part 2: General use containers
    • ISO 90-3:2000 Part 3: Aerosol cans
  • ISO 91 Petroleum measurement tables [Withdrawn: replaced with ISO 91:2017]
    • ISO 91-1:1992 Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F
    • ISO 91-2:1991 Part 2: Tables based on a reference temperature of 20 degrees C
  • ISO 91:2017 Petroleum and related products - Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions
  • ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of side (left or right)
  • ISO 93 Textile machinery and accessories—Cylindrical sliver cans
    • ISO 93-1:2006 Part 1: Main dimensions
    • ISO 93-2:2006 Part 2: Spring bottoms
  • ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning and ring-doubling frames
  • ISO 96 Textile machinery and accessories—Rings and travellers for ring spinning and ring twisting frames
    • ISO 96-1:2016 Part 1: Flange rings T and SF and their travellers
    • ISO 96-2:2009 Part 2: HZ- and J-rings and their travellers
  • ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and twisting for ear-shaped travellers [Withdrawn: replaced with ISO 96-2]
  • ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning machinery—Main dimensions of coverings for top rollers
Other Languages